|Your cart is currently empty|
The Model 133 automatic door opening system enables complete independence when entering and exiting a residential or public / light commercial door. The Model 133 is designed for any free swinging door like residential front doors, office doors, apartment doors, bathroom doors, etc. This professional grade system includes an electric strike to unlatch a locked door, then opens, pauses and closes it – all automatically.
Automatic door operator shall be electromechanical, and provide for both powered opening and powered closing of a door. The door opener shall provide no influence upon the door except when it is actively involved with powered opening, holding open, or closing, thus allowing unencumbered manual operation.
The unit shall contain an internal battery power supply to provide powered operation in the event of external power failure. The unit shall be powered by 24 vac, external to the device under provisions of low voltage wiring and is supplied with a 20 VA transformer requiring 115 vac 60 Hz service.
The operator shall be mounted according to drawings and instructions provided with each unit. The unit shall be capable of mounting on either door or lintel and shall provide door opening angles up to 120 degrees.
The unit shall possess an adjustable hold-open feature allowing the door between 5 and 30 seconds for passage. The unit shall stop when encountering an obstruction during an operating cycle at which time it ceases to provide an influence on the door.
Electro-mechanical. Power open, power close. Automatic clutch disengagement at all times when not activated, allowing unimpeded manual operation.
Automatic open-hold-close cycle (5 to 30 seconds) activated by a signal from internal radio receiver or the momentary closure of electrical contacts provided by wires to unit.
Automatic cycle may be interrupted by a signal received within the cycle bringing the operator into a disengaged state. Door may be closed remotely if door is found left open in a nonactive state upon receipt of a signal.
Optional Mode (Auto-Close setting) - causes door to close automatically after a delay upon manual opening. Can be brought into activation in one of three ways:
Provision of electrical wires to unit to provide a discontinuity between internal contacts.
Provision of discontinuity of contacts upon installation.
Removal of 24 vac external power to operator.
Operator: 16-24 vac/dc
Wall Transformer: Input - 115 vac, 60 Hz; Output - 24 vac, 20 va
Battery: 12V DC, 1.2Ah sealed lead-acid battery
Motor: 12V DC, 1.5A
Clutch: 12V DC, 0.5A
Supply for Unlatching Device: 12V DC, 1A
Radio Receiver: Up to 1 Billion Security Code Combinations (Programmable)
Dimensions: 2 5/8” x 4” x 14 1/8” (Suitable for mounting with perpendicular wall close to door frame.)
Weight: 10 Lbs.
Material/Finish: Steel housing; Powder coated finish
Door mounted for inward and outward opening doors in either right-hand or left-hand hinged configurations. (Ceiling clearance 1 1/4” minimum between door and ceiling). Lintel mounted for inward and outward opening doors in either right-hand or left-hand hinged configurations.
Activation may occur by coded signal from transmitter or by wireless security entry system. Activation contacts are provided within unit for remote wired activation from any device providing momentary continuity such as touchplates, pushplates, mats, or infrared motion sensors
During the first year Open Sesame will replace, exchange, repair all factory supplied components of our door operator free of charge. The course of action necessary to return your door operator to a functional state is solely at the discretion of Open Sesame Door Systems, Inc. After the first year; Open Sesame will replace, exchange, or repair all factory supplied components on a fee basis not to exceed $450.00 for an additional 5 years. This warranty excludes replacement of batteries for remote controls or the battery in the operator itself. Open Sesame Door Systems, Inc. is not liable for incidental or consequential damages. Some jurisdictions do not allow exclusion or limitation of incidental or consequential damages, so the above exclusion may not apply to you. This warranty, also give you specific legal rights, and you may have other rights that may vary from State to State.
Remote Control: Standard Remote with sensitivity paddle included.
Electric Strike: Wired to the door opener, wht electric strike is used to release the door latch. The Open Sesame system incorporates the use of a door release mechanism installed in the door frame. Similar to getting “buzzed in” an apartment building, when activated, the electric strike releases the door latch and allows the electric operator to open the door.
Low Voltage Wiring Kit: Open Sesame automatic door openers use a low voltage 24-volt wiring kit ensuring that electrical installation is easy and does not requiring an electrician.
Most installations take less than 2 hours – far less time and labor than most other door openers. Plus there’s no need to hire an electrician, since the Open Sesame door opener is a safe low voltage device. Just plug in the 24 volt AC adapter to the nearest (within 30 ft) wall outlet, plug in the door opener to the small wall mounted junction box, and you’re set.
Universal Mounting Types
Door Mount: Used for inward opening doors.
Lintel Mount: Used for outward opening doors.
Parallel Mount: For outward opening doors that require a wider opening angle or have a recess. Also used for storm door and screen door applications.
Checking and Charging the Battery
Standard Transmittter: Standard one-button remote included or other remote options are also available. Standard Transmitter
This transmitter is a visor transmitter which may be mounted below the wheelchair armrest or a side panel. A sensitivity paddle is included to make it easier to push. Size: 3.25” x 1.25”x 0.5”
Promixity Sensor: The sensor will activate the door when a smart tag is within the area of detection with no hand use required. The area of detection has three distance settings: 3 ft, 6 ft, 9ft. One reader will work from both sides of the wall. It comes with two proximity tags. Available in white and black.
The sensor will activate the door when a smart tag is within the area of detection with no hand use required. The area of detection has three distance settings: 3 ft, 6 ft, 9ft. One reader will work from both sides of the wall. It comes with two proximity tags. Available in white. RFID Transmitter Size: 4.25”x 2.25”x 0.75”; Sensor Tag Size: 1.5”x 1.5”
Keyless Entry: This wireless keypad, which is mounted outside of the door, eliminates dependence on keys for care providers or visiting family members by allowing entry with a code.
Spec Switch: This is a sensitive switch for people with very limited hand use.
This wireless keypad, which is to be mounted outside of the door, stops dependence on keys for care providers or visiting family members by allowing them to enter by pushing a 4-digit combination code which can be changed easily when care provider is no longer a member of the household staff. Size: 7”” x 2.5” x 1.25”
Voice Interface: New, easy to install Voice Interface switch allows you to connect your Open Sesame door operator to wifi and Amazon Alexa. Can be added to any existing units operating on the 433 MHz frequency.
Large Wireless Wall Push Pad: This large push pad is designed for more abusive environments and is very tamper-proof. It has a thick metal push plate designed with the handicapped logo and “Push to Open” label. Size: 5”x 5”
Keychain Transmitter: This transmitter is a one button key chain style mini transmitter for use by individuals who have full hand use. Small size allows storage in purse or chair side pouch. Size 2.5””x 1.375”x 0.5”
Please fill out the form below to request a product quote. A representative will respond to you via email or phone as soon as possible.