Your cart is currently empty |
Subtotal: | $0.00 |
SEAT: | |
ARM: | |
MECH: | |
HEADREST: | |
BASE: | |
CASTERS/GLIDES: | |
STOOL CYLINDERS: | |
FOOTRINGS FOR STOOL CYLINDERS ONLY: | |
Skin: | |
Upholstered Arm Pad Only available on (2) arm: | ADD (Add $91.65) |
N∙dulgent Memory Foam: | ADD (Add $105.75) |
N2 - ThermaGel Memory Foam: | ADD (Add $126.90) |
Connexion Arm Not available with (6) or (7) Arm: | ADD (Add $493.50) |
Connexion Tablet Holder Requires (Z1) Connexion Arm: | ADD (Add $210.09) |
High mesh back & contoured seat design
Passive weight dispersion design
Generous foam for optimal comfort
Convert mesh back to upholstered with optional sleeve
Independent lumbar adjustment
2 headrest options
No Arms
26" Black Base
Carpet Casters
8" Cylinder
Adjustable Lumbar
6 - Medium Seat
7 - Large Seat
0 - 4" Adjustable *
1 - 4" Adjustable w/Pivot *
2 - Lateral Sliding *
3 - 3" Adjustable
4 - Swing *
5 - No Arms (Default)
6 - C Loop *
7 - Chrome Loop *
8 - 360° NP Only available on (2) synchro mech *
9 - 5-way Adjustable
* Delay
2 - Synchro
6 - Multi-Tilt
HE - Height Adjustable
H4 - Dual Pivot Matching up
H5 - Dual Pivot Black faux leather
B0 - Standard
26" - Black
B6 - 26" Polished Aluminum
B8 - 26" Brushed Aluminum
C1 - Hard Floor
C2 - Glides
L1 - 3" Cylinder
L3 - 5" Cylinder
L13 - 7" Dual Stage
L14 - 10" Dual Stage
L5 - 10" Cylinder
L7 - 7" Cylinder
R1 - 18" Black Plastic
R2 - 20" Chrome
R8 - 8" w/Casters
R10 - 10" w/Casters
R18 - 8"/10" w/Casters
RW8 - Wide 8" w/Casters
RW10 - Wide 10" w/Casters
S1 - Grade C or 1
S2 - Grade 2
S5 - Ultraleather
J - Upholstered Arm Pad Only available on (2) arm
N - N∙dulgent Memory Foam
N2 - ThermaGel Memory Foam
B6 - 26" Polished Aluminum Base
Z1 - Connexion Arm Not available with (6) & (7) arm
A1 - Connexion Tablet Holder Requires (Z1) Connexion Arm
SKU: RCT4
1. Independent Lumbar - To position lumbar height, locate the support inside the backrest frame and move it up or down in a 3” range of motion.
2. Forward Tilt-stop - Your chair can be set to tilt forward, past horizontal and locked in position. Before adjusting, recline the seat slightly. Rotate the control rod to allow variable degrees of forward tilt.
3. Back Angle - Seated upright, lift the back angle lever and position the backrest as you choose. Then release the lever to lock it. This lever will lock in a free-float mode.
4. Seat Height - Lift the lever while not seated to increase height. Lift the lever while seated to decrease height.
5. Seat Angle - Lift the lever to release the seat. If you desire a rocking mode, lift the lever fully upward. Push the lever down again to lock seat tilt.
6. Seat Tilt Tension - Twist the control forward to increase tension or rearward to decrease tension
7. Seat Slider (Depth) - While seated, lift the lever to slide the seat forwards and backwards. This is usually a one time adjustment.
8. Arm Width - Easily adjusted from the seated position. Snap the latch open (away from arm) to unlock, and then position the arm to as desired. Snap the latch closed again to secure that setting.
9. Arm Height - For armrest height, locate the button on the outer arm support and squeeze it while positioning the arm, and then release to lock into your chosen setting.
1. Independent Lumbar - To position lumbar height, locate the support inside the backrest frame and move it up or down in a 3” range of motion.
2. Seat Tilt Tension - Rotate it forward to increase tension or turn the control backward to decrease tension.
3. Seat Height - Push the lever down and lift your weight to raise the seat to the desired position. To lower the seat, push the lever down while remaining seated.
4. Seat Slider (Depth) - Lift the lever to activate seat slider.
5. Seat & Back Synchronies Angle - While seated, twist the left side control forward to release seat into rocking mode. Slight rearward pressure against the backrest may be required to regain rocking
mode. Lock in any of 5 preset positions by holding that position and rotating the control rearward.
6. Arm Width - Pull the switch away from the arm to unlock, and then position the arm width. Snap the switch closed to secure your setting.
7. Arm Height - Squeeze the button while positioning the arm, and then release to lock into your chosen setting.
Please fill out the form below to request a product quote. A representative will respond to you via email or phone as soon as possible.